Get the Best IPTV Service
Search results for query: * | SatelliteGuys.US

Search results for query: *

  1. C

    coolsat6000 reboots every 2sec.

    Thank you. Found firmware. Was able to load the firmware. Problem fixed.
  2. C

    coolsat6000 reboots every 2sec.

    Thank you.
  3. C

    coolsat6000 reboots every 2sec.

    Thank you. Where do i find the firmware.
  4. C

    coolsat6000 reboots every 2sec.

    Hi, need help I was watchig tv and my coolsat6000 started to reboot by it self. The box is not modified. Any idia. Thank you
  5. C

    Loosing signal when changing chanels

    I'll try Thanks
  6. C

    Loosing signal when changing chanels

    It happends on "H" polarity. Wich are good LNBs?
  7. C

    Loosing signal when changing chanels

    Hallo all, I have cs4 and cs6 connected through two separate diseq switches to two dual lnb receiving from two sats. When i change chanel on one receiver i am loosing signal on the other receiver for 1 to 3 seconds (bad or no signal). What is wrong? Please advise. Thanks
  8. C

    cs4000pro, no 13V and 18V

    I am glad too that is fixed. The heatsink is under power and is isolated from gnd ( the tab of LM317 is under power - the ouput, You are correct) Thanks for the help again.
  9. C

    cs4000pro, no 13V and 18V

    Problem solved HI, and Thank You. I replaced LM317 as You sugested and bang everething is ok. Now I have 13V, 18V, and 0V when off. When I removed IC I noted that there was no heat transfer compound between heat sink and IC. I did it the proper way and now is ok Thank You guys You are grait.
  10. C

    cs4000pro, no 13V and 18V

    Hi again. I was going to go in bed, then I sed I have to check it now. So 10ohm drops output voltage to 21.51V only. I will buy Lm317 and will cross my fingers. Thanks again for the support.
  11. C

    cs4000pro, no 13V and 18V

    Hi, I just found 10ohm resistor. I will test again and if i dont get 1.25V I vill replace LM317. Thank you.
  12. C

    cs4000pro, no 13V and 18V

    Hi, and thank you. I did not have at the moment 10ohm resistor. I found 1k. If does not help al buy 10 ohm and will check again. Grounded adj pin with 1k as it is on the board (assuming there is ~2.7k to gnd in circuit) so will get less than 1k to gnd. Voltage on output changed from 23.74v...
  13. C

    cs4000pro, no 13V and 18V

    Very funy! Hi, thanks to you I needed 1h and found that it is LM317 - 3-terminal adj. voltage regulator- wich controls the voltage to LNB. Possibly controled by transistor pnp on adj pin on input = 23.82V output = 23.76V adjust = 21.6V I found that resistance betw. input and output is...
  14. C

    cs4000pro, no 13V and 18V

    Thank You very much. It sounds very profesional. I will try this and I will let you now. Thank you
  15. C

    cs4000pro, no 13V and 18V

    Tried. Does not change voltage. Thanks
  16. C

    cs4000pro, no 13V and 18V

    No. I am using factory installed software. I am afraid to connect it in this condition. Is it software or hardware problem? Thanks
  17. C

    cs4000pro, no 13V and 18V

    Hi, need help. I have coolsat4000pro. I mesure 23VDC on connector to LNB - back of receiver. I don't mesure 13VDC and 18VDC needed for LNB operation. The 23V is even present with LNB power off in dish settings. Please, need help how to fix. Thank You
Top
Flash Sale Popup