You are absolutely right. It's all done. He's sending some folks out to the house tomorrow. Impressive!

Thanks Speedy...just noticed that you are Dish Network Customer Service.

Thanks Speedy. I'll give Dishnetwork a call.

I have the same problem. What is the solution?

I have the same TV and I haven't found a code that works either. I noticed that there is a new learning remote from Dish Network. Maybe you can try to get one.

...TVs using the modulated signal from the 622 and the picture quality is impressive. This message is to confirm that RG59 works without adding extra filters/amps and such. Very nice box from E*. On further note, I was not that pleased with the 811 and now I am very glad that I upgraded to the 622.

Audio dropouts for me too. Fortunately, it can be remedied by flipping channel up and back down. I also noticed the "All HD" favorite list. I don't think it was there before but it is a nice addition.

Does Rave ever follow their schedule? This is the third time I've tried to auto record The Cure Trilogy and some other programming is on. What gives? Or is this normal for the Rave channel to never follow their schedule?

...experiment first since the cabling is already there. The only thing I was worried about was that the RG59 wouldn't work. I already knew that the E* requires RG6 for the satellite signal because that was mentioned in the installation guide. However, the guide does not mention a particular...

My house is pre-wired with RG59 coaxial cables to 4 rooms. I am about to use the modulated output of the 622 to send programming through the existing cabling within my house. My question is, should I bite the bullet and replace the RG59 with RG6? Or Does it matter?

DANG! Why would I subscribe to HD locals if I get it with the OTA?

Nope...I didn't subscribe to locals when I had the 811 either.

The channel guide for every OTA channel has "Digital Service" printed on the new 622. I've tried rescanning and rebooting but I cannot seem to get any listings for the OTA channels. Before upgrading to the 622, the 811 channel guide had listings for the OTA channels. Is there some setting that I...

Thanks for everyone's input. The problem is resolved. I reset the unit 3 times without any success. The fourth time, I decided to unplug the VIP622 for a "hard" reset and that seems to work. Weirdest bug I have ever encountered because originally, the Caller ID history had all the test calls...

Caller ID was working fine with the 811 so I don't think the issue is with call forwarding. I also have a DSL filter attached. Again, I can see in the Call ID history on the VIP622 that calls are recorded. The only issue is that there is no pop up window on the TV screen when a call comes in.

The phone line is the same one that was plugged into the 811 of which I had swapped out for the VIP622. The Caller ID feature worked well with the 811 and I do subscribe to Caller ID with the phone company. In fact, my phone will display the caller ID when I get a call (to put to rest that...

I tried your suggestions: 1. Visual check shows that the phone line is in the phone jack (not ethernet port) of the VIP622 unit. 2. I went to Menu->System Setup->Diagnostics->Connection and it is says "Phone Connection OK" after it went through the Testing Phone Connection phase. 3. I went...

I use the Winegard Squareshooter antenna in my attic and the channels that were %49 on my 811 does not show up on the VIP622. However, the channels that were on the "edge" (%52-%59 and pixalation) with the 811 are now at %65 and steady with the VIP622. The channels with much better strength had...

I'm not sure if there is a bug with the Caller ID function or it may be my mistake but the Caller ID doesn't seem to work. I've received numerous calls today and the Caller ID did not appear on the screen. I enabled the Caller ID by doing the following: Menu->System setup->Installation->Caller...

Just got mine installed and it is working great! Fan noise was loud at boot-up but quited down since. My installation experience is great. The installer was in/out in about an hour after hooking up new dish1000 and 622. All programming is set correctly. The OTA channels are much more stable than...

Just got the 622 today. It came via UPS. Now I have to wait for the installer to come on 2/28. The temptation to rig it up myself is going to drive me nuts between now and the 28th.

So the guide here http://dishnetwork.tvlistings.zap2it.com/dishsite/listings/gridall.asp doesn't work for you?

Before I take the plunge into upgrading from the 811 to the 622, I'd like to know if there are any glitches or bugs that are of concern. I am worried that I may be putting cash into something that needs a bunch of software revs before it is a worthy product. When I shelled out for the 811 a few...

How do you erase the cookie? Or is it too late? I know an insider named "Elvis" at E* that could help me out. I'll check with him and will let you know what I find out. Also, "Elvis" mentioned that Bush's CIA folks are monitoring this site too...just an FYI.

I live in Mebane, NC and I have found this site to be very helpful. http://www.hdtvmagazine.com/programming/broadcast.php